Re: DataCAD 19 Wishlist
Posted: Fri Oct 27, 2017 7:28 amAwesome - thanks!
Add option to purge on exit, to purge Helplines when exiting.
Until then, this alias works
[d]
comment=delete Helplines
alias=^:^S4^F1^F5^
forum.datacad.com
DataCAD Forum Hosted by DATACAD LLC
https://www.datacad.com/bbs/
DataCAD 19 Wishlist
Page 3 of 3
Posted: Fri Oct 27, 2017 7:28 amRe: DataCAD 19 Wishlist
Posted: Tue Oct 31, 2017 12:57 pmRe: DataCAD 19 Wishlist
Posted: Wed Nov 15, 2017 10:43 amOkay - I think it would be AMAZING if we could Move / Drag and entity - and then have Dynamic Rotate and Dynamic Flip available when we place it.
I am working in a file that is an imported DWG, and a lot of symbols are mirrored and / or rotated, and having these options would be a BIG help.
I am working in a file that is an imported DWG, and a lot of symbols are mirrored and / or rotated, and having these options would be a BIG help.
Re: DataCAD 19 Wishlist
Posted: Wed Nov 15, 2017 11:01 amooh! so amazing and such a big help!! Even for everyday stuff too.
I second Neil's wish.
I second Neil's wish.
Re: DataCAD 19 Wishlist
Posted: Wed Nov 15, 2017 12:04 pmNeil Blanchard wrote:...it would be AMAZING if we could Move / Drag an entity - and then have Dynamic Rotate and Dynamic Flip available when we place it.Use Cut/Copy and Paste, and your wish shall come true.
Re: DataCAD 19 Wishlist
Posted: Wed Nov 15, 2017 3:25 pmOkay, that does it essentially. It takes a few additional clicks and keyboard shortcuts, though.
M / F1 / Left Click then hold Shift and / or Control, then Left Click.
vs
Control E, select entity(ies), click insertion point (or toggle on At Center), then click Cut. Then Control V, then hold Shift and / or Control, then Left Click.
M / F1 / Left Click then hold Shift and / or Control, then Left Click.
vs
Control E, select entity(ies), click insertion point (or toggle on At Center), then click Cut. Then Control V, then hold Shift and / or Control, then Left Click.
Re: DataCAD 19 Wishlist
Posted: Thu Dec 14, 2017 8:50 amIn the drawings I am working in, which are imported DWG's there are a number of symbols that are duplicated exactly on top of each other. Would it be possible to scan the drawing to find all these?
Re: DataCAD 19 Wishlist
Posted: Mon Dec 18, 2017 2:59 pmA couple of wish list items:
In 1-Line Trim, could we have Previous Line as an option?
And this may be more of a fix: Alt-I on Paratext doesn't set the (line spacing) Factor.
In 1-Line Trim, could we have Previous Line as an option?
And this may be more of a fix: Alt-I on Paratext doesn't set the (line spacing) Factor.
Re: DataCAD 19 Wishlist
Posted: Mon Dec 18, 2017 3:16 pmNeil Blanchard wrote:In 1-Line Trim, could we have Previous Line as an option?
It's already there. It only shows up in the menu if a valid line has previously been entered.
Re: DataCAD 19 Wishlist
Posted: Mon Dec 18, 2017 3:18 pmDavid A. Giesselman wrote:Neil Blanchard wrote:In 1-Line Trim, could we have Previous Line as an option?
It's already there. It only shows up in the menu if a valid line has previously been entered.
You're right, of course. I entered a couple of lines, but I either didn't see it, or it was not a "valid line".