What features would you like to see added to a future version of DataCAD?
#70796 by Mark Bell
Mon Feb 13, 2017 1:49 am
Add a new command in the Utility Menu / S4 Convert which would allow :

1. Pick a selection of 2D lines , arcs etc. using EGAFM then convert to a :
a) polyline,
b) covered polyline,
c) with fills
d) with knockout
e) to a smart wall
f) with new z-b/z-h settings
g) to a symbol
h) to an xref
#70798 by Mark F. Madura
Mon Feb 13, 2017 4:39 pm
It sounds like you're looking for a Change Entity command. In the meantime...

To convert lines and arcs to polylines:
- Go to Curves, Polyline, Edit and toggle on Line to Poly.
Note: Toggle off Keep Lines if you do not want the original lines to remain.
- The prompt says, Select start point of polyline.
- Clicking on a line or arc will convert it to a polyline, and it will remain highlighted.
- You can continue clicking on additional entities while you're in this mode.
Note: You cannot select entities to convert by Area.

To 'add' a cover to a closed polyline:
- Go to Curves, Polyline, Edit and toggle on Toggle Cover.
- The prompt says, Select polyline to add/remove the cover.
- Clicking on a closed polyline will add or remove the cover.
- You can continue clicking on additional entities while you're in this mode.
Note: You cannot select polylines to edit by Area.

To add a fill to a polyline:
There are several ways to add a fill to a polyline.
Here is the primary method.
Note: Only closed polylines can be filled.
- Go to Hatching, SPB-Fill.
- Click on the polyline you would like to fill.

To add a knockout to a polyline:
- [CTRL] + Right-click on a polyline.
- Select KnockOut from the Context Menu.

To convert polylines to Smart Walls:
Note: It is not currently possible to convert lines and arcs to Smart Walls. They must be converted to polylines first.
- Go to Architect, make sure Auto 3D is toggled on, and select Edit Walls.
- Select Poly to Wall.
- The prompt says, Select polyline to convert to walls.
- Click on a polyline to convert it to a Smart Wall.
- The prompt says, Click a point to define the inside of the wall.
- Click on one side of the polyline to indicate the inside.
- You can continue selecting additional entities while you are in this mode.

To change the z-base and z-height settings for an entity or multiple entities:
- Go to Change, toggle on Z-base (and/or Z-height).
- Enter the new Z-base/height value.
- Toggle Entity to change one entity at a time.
- Toggle Area to draw a box that fully-contains all of the entities you would like to change.
- Press [CTRL] + [A] if you would like to select ALL entities (based on Layer Search).

To convert entities to a Symbol:
- Press [CTRL] + [E] to go to Clipboard Select.
- The prompt says, Select entity to Cut/Copy to the Clipboard.
- Click on an entity to highlight it.
- Continue clicking additional entities to add them to your selection.
- When you're finished selecting entities, select Copy.
Note: If Insert Pnt. was toggled on, the prompt will say, Enter the insertion point.
- Once you've copied the entities to the Clipboard, select the Edit pull-down menu.
- Select Paste As Symbol.
- The prompt says, Enter a name for this Symbol.
- You can enter a specific name, or accept the one that is automatically-generated.
- Place the symbol in your drawing.
Note: If you right-click before placing the symbol, it will still be available in the header of your drawing.

To convert a Symbol to an XREF:
- [CTRL] + Right-click on a symbol.
- Highlight Symbol Tools in the Context Menu, then select Convert to XREF.
- A File Dialog will appear.
- Enter a new name for the external file, or accept the default name.
- Select Save.
Note: To convert an XREF to a Symbol, select the Bind sub-menu in XREF Tools in the Context Menu.
#70801 by Mark Bell
Mon Feb 13, 2017 5:09 pm
Hello Mark,

Thanks for the detailed list of options. I am aware of each of these and already use them. The reason for the post was to consider consolidating the various menus and macros into a single menu that handles a multitude of changes from the one menu. You've also answered the wishlist of creating a polyline entity using Area and that it's not currently available....maybe Contour Search could be added to bypass the need to manually trace around the lines/arcs when creating a polyline?
....Change Entity is probably a better menu name than Convert.
Thanks.
#70822 by dmartens
Wed Feb 15, 2017 2:38 pm
I can fill an open polyline in 15. And if you select a polyline to fill the polyline goes away.

Who is online

Users browsing this forum: No registered users and 27 guests

About DataCAD Forum

The DataCAD Forum is a FREE online community we provide to enhance your experience with DataCAD.

We hope you'll visit often to get answers, share ideas, and interact with other DataCAD users around the world.

DataCAD

Software for Architects Since 1984